Psion Teklogix PowerScan M8300 Instrukcja Użytkownika Strona 158
- Strona / 220
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
REFERENCES
141
5.1.2 ACK/NACK Protocol
PowerScan
®
D8330 Readers
This parameter sets a transmission protocol in which the Host responds to the reader
after every code transmitted. The Host sends an ACK character (06 HEX) in the case
of good reception or the NACK character (15 HEX) requesting re-transmission, in the
case of bad reception.
PowerScan
®
D8330 Host
ACK or NACK
data
cable
ACK/NACK enabled
If the reader does not receive an ACK or NACK, transmission is ended after the
RX Timeout (see section 5.1.4).
When ACK/NACK protocol is enabled, FIFO must be disabled manually, see section
5.1.3.
PowerScan
®
M8300 Readers
The transmission protocol takes place between reader, cradle and Host. The reader
passes its data (code read) to the cradle, which sends it to the Host. The
management of responses (from Host or cradle) depends on the Transmission Mode
parameter, see section 5.9.4.
In the followi
ng descriptions the completed transmission is indicated by the Beeper
Control for Radio Response parameter with its default setting to Normal, see section
5.9.5.
When ACK/NACK is disabl
ed (in One-Way tx mode), there is no control from cradle
to Host transmission, the reader responds with the good reception tone.
BC-80X0
Host
data
cable
PowerScan
®
M8300
data
Transmission Mode = One
-
Way
good RX
beep
ACK/NACK disabled
- Psion Teklogix 1
- PowerScan 1
- D8330/M8300 1
- COMPLIANCE 7
- LASER SAFETY COMPLIANCE 9
- LED CLASS 10
- IC (INDUSTRY CANADA) 10
- 1999/5/EEC R&TTE 11
- CONTENTS 13
- GENERAL VIEW 16
- Figure C – BC-8000 17
- Figure D – C-8000 17
- 1 INTRODUCTION 18
- 2 INSTALLATION 19
- INSTALLATION 20
- CAUTION 20
- 2.3 RS-232 CONNECTION 22
- 2.4 USB 22
- 2.5 IBM USB POS 23
- 2.6 WEDGE CONNECTION 24
- 2.8 NETWORK CONNECTIONS 25
- 2.8.2 Network Cabling 26
- 2.8.3 Network Termination 27
- 2.9.2 Replacing PowerScan 28
- M8300 Batteries 28
- 2.9 POWERSCAN 28
- M8300 BATTERY MAINTENANCE 28
- 2.9.1 Battery Charging 28
- 2.10.1 Desktop Mounting 30
- Portable Desktop Use 31
- Fixed Desktop Use 31
- 2.10.2 Wall Mounting 33
- Inclined Base Wall-mounting 34
- 3 POWERSCAN 35
- M8300 SYSTEM AND NETWORK 35
- LAYOUTS 35
- 3.1.4 C-BOX Layout 37
- 3.2.1 Host Master Layout 38
- 3.2.2 BC-8060 Master Layout 39
- /*32: FAIL*/ 40
- 4 CONFIGURATION 41
- 4.1.3 Copy Command 42
- 4.2 SETUP PROCEDURES 42
- Ì$+$*oÎ 44
- ÌIB'Î 45
- ÌRA0RFHÎ 46
- Ì$+RN0$-IÎ 46
- Ì$+RX0$-qÎ 47
- Ì$+RN1$-NÎ 47
- 4.5.2 PowerScan 48
- 4.6 POWERSCAN 49
- M8300/STAR-SYSTEM™ SETUP 49
- Ì$+RF4Î 51
- Ì$+RZ2$-ÇÎ 52
- Ì$+RZ1$-~Î 52
- Ì$+CP0$-$Î 53
- Ì$+CM2EC0$->Î 53
- Ì$+CM1$-ÈÎ 53
- Ì$+CM0$-ÃÎ 53
- Ì$+CP6$-BÎ 53
- First Start-Up 56
- CONFIGURATION 58
- RS-232 PARAMETERS 59
- ANDSHAKING 61
- USB PARAMETERS 64
- USB-COM 65
- USB-KBD 67
- EYBOARD 67
- ATIONALITY 67
- WEDGE PARAMETERS 70
- HARACTER 76
- MULATION 76
- PEN EMULATION 77
- PERATING 78
- NETWORK PARAMETERS 82
- ERMINATOR 86
- DATA FORMAT 87
- DJUSTMENT 93
- EPLACEMENT 95
- POWER SAVE 100
- READING PARAMETERS 101
- NTENSITY 104
- DECODING PARAMETERS 107
- CODE SELECTION 110
- Ì#+AUTOWÎ 111
- ADVANCED FORMATTING 128
- ONCATENATION 129
- DVANCED 132
- ORMATTING 132
- RADIO PARAMETERS 147
- ONTROL FOR 150
- DISPLAY PARAMETERS 153
- 5 REFERENCES 157
- 5.1.2 ACK/NACK Protocol 158
- 5.1.3 FIFO 159
- 5.1.4 RX Timeout 160
- 5.2 PEN PARAMETERS 160
- 5.2.1 Minimum Output Pulse 160
- 5.2.3 Overflow 161
- 5.2.5 Inter-Block Delay 162
- 5.3 NETWORK PARAMETERS 162
- 5.4 DATA FORMAT 163
- POWERSCAN® D8330/M8300 167
- (accent) 168
- ÌFQ9C2>Î 170
- 5.4.3 Address Stamping 172
- 5.4.4 Address Delimiter 172
- 5.4.5 Time Stamping Format 173
- 5.5 POWER SAVE 173
- 5.5.1 Sleep State 173
- REFERENCES 174
- 5.6.5 Safety Time 175
- 5.7 DECODING PARAMETERS 175
- 5.7.1 Ink-Spread 175
- 5.7.2 Overflow Control 175
- 5.7.3 Interdigit Control 176
- 5.8 ADVANCED FORMATTING 176
- 5.8.1 Match Conditions 176
- 5.9.2 Radio RX Timeout 177
- 5.9.3 Power-Off Timeout 177
- 5.9.4 Transmission Mode 178
- 5.9.6 Single Store 179
- 5.9.7 Batch Mode 179
- 5.9.8 Find Me (PowerScan 180
- M8300 only) 180
- 5.10.1 Display Mode 181
- Ì$+$0ÂÎ 183
- Ì$+$1$Î 183
- Ì#+CODEÂÎ 183
- Ì$+ZZ0$-*Î 184
- Ì$+ZZ2$-4Î 185
- Ì$+ZZ3$-9Î 186
- Ì$+RN2$-SÎ 188
- 6 MESSAGE FORMATTING 189
- 6.1.1 Cursor Control 190
- 6.1.2 Font Selection 191
- 6.1.3 Clearing Display 191
- 6.1.5 Setting RTC 192
- 7 TECHNICAL FEATURES 194
- 7.2 POWERSCAN 195
- 7.3 BC-80X0 / C-8000 196
- 7.5 STATUS INDICATORS 197
- 7.6 READING DIAGRAMS 200
- POWERSCAN 201
- SERIAL CONFIGURATION STRINGS 202
- (ms) CK00 - CK99 203
- (100 ms) CL00 - CL99 203
- (not for USB-KBD-ALT-MODE) 204
- (IBM AT compatible only) 204
- (100 ms) CK00-CK99 206
- (only for D8330 series) 209
- B CODE IDENTIFIER TABLE 215
- C HEX AND NUMERIC TABLE 218
- HEX / NUMERIC TABLE 219
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji